artikel_direkt.htm | t_responsepage

Not logged in

Cart (0)
0,00 €
Freight: 0,00 € (0 kg)

New products
Special offers

Product Details


  • For Epoxy-, polyester- and vinylester resins
  • Silicone-free
  • Useable up to 60 °C

A blend of hydrocarbon and microcrystalline waxes. For high-gloss surfaces. Ideal for smooth and sealed surfaces e.g. on GRP moulds.

Polishing possible after a drying time of approx. 1-2 minutes.

Could be used in conjunction with film release agent PVA.

Available in green and colourless.

It is particularly recommended for use on moulds where standard silicone waxes hinder post-finishing operations or as a primer coat prior to the application of PARTALL® Coverall Film.PARTALL® Paste #2 may also be employed as an economical edge wax on larger molds, and is used to seal rough wood moulds or plugs for casting composites, cements and grouts.

The maximum processing temperature is 60 °C.

Mould surface preparation
Before application of PARTALL® Paste #2 porous molds (i.e., plaster or wood) should first be cleaned and sealed. Composites grade sealers and fairing compounds (body filler) are recommended but a good surface on plaster or wood may be obtained with automobile type primer-sealers and lacquers. For non-cosmetic parts with rough wood molds or plugs a number of coats of PARTALL® Paste #2 should adequately seal the surface.

Using a clean and dry cotton cloth, apply a small amount of Partall® Paste #2 to mould surface in a thin even coat. Turn over cloth and begin buffing immediately by hand (within one minute after application). On larger moulds or plugs work on smaller sections at a time or have second operator follow to polish. Power buffer equipped with a terry cloth or lamb’s wool pad will reduce labor time on larger moulds. Surface should be buffed to a glossy finish. Complete surface coverage is more important than a thick film of wax. In order to ensure complete coverage, repeat application and polishing process at least 3 times for initializing new or reconditioned moulds or plugs. Alternate direction of application of each coatimportant (i.e., 0°, 90°, circular, etc.). Polish each coat before applying the next.

Please note:
For mould surfaces that are extremely smooth (low to no surface roughness), it is advisable to polish carefully or better not at all, as otherwise there is a danger that the release agent application will be removed again (at least in places).
In the original Rexco manual which we have translated here, the author assumes that the user is a professional processor from trade and industry who has the appropriate routine in the processing of composites and therefore also with release agents.
If you do not yet have this experience as a first processor, we recommend that you refrain from polishing until you have a feeling for the wax build-up and the release effect. It is better not to polish the release wax or only to polish it very little and carefully, and later remove a component from the mould with a silk-matt glossy surface than to polish a mirror-smooth mould surface and then possibly not get the component undamaged out of the mould, as it partially sticks to the mould surface.

More info see (in german, translator included) R&G Wiki

Variant Selection

PARTALL® Paste #2 (colourless) tin/ 680 g

(680 g = 24 oz)
12 in stock  (delivery time 1-2 days) Order no.: 1651601
15,35 € (Base Price 15,35 € /  pc.)

Scaled Price

  • From Qty 2: 5,0%
  • From Qty 3: 10,0%
  • From Qty 6: 15,0%
  • From Qty 12: 20,0%
  • From Qty 24: 25,0%
  • From Qty 48: 30,0%

PARTALL® Paste #2 (green) tin/ 680 g

(= 24 oz)
33 in stock  (delivery time 1-2 days) Order no.: 1651651
15,15 € (Base Price 15,15 € /  pc.)

Scaled Price

  • From Qty 2: 5,0%
  • From Qty 3: 10,0%
  • From Qty 6: 15,0%
  • From Qty 12: 20,0%
  • From Qty 24: 25,0%
  • From Qty 48: 30,0%

all Prices  price incl. VAT, possibly plus shipping


Rate item

Rating for PARTALL® Paste #2 (colourless + green), 680 g

My rating

My data

Your E-mail address will not be published